ProQuest Subject Index - Mechanical engineering at THE UNIVERSITY OF TEXAS AT ARLINGTON

TOP >> THE UNIVERSITY OF TEXAS AT ARLINGTON >> Mechanical engineering

Browse Institutions

You are viewing titles for THE UNIVERSITY OF TEXAS AT ARLINGTON in the Mechanical engineering available through the UMI Dissertations & Thesis Gradwoorks site

Thermal enhancement of stacked dies using thermal vias	Structural analysis of fiber reinforced composite materials

Finite element modeling of carbon nanotube reinforced polymer composites and evaluating its thermal conductivities	Design and optimization of heat spreaders and selection of fan in laptop

Computer-aided patient specific treatment planning of cryosurgery for breast cancer	Micromechanical analysis of yielding for particulate filled composites

Freezing-induced microstructural changes of collagen scaffolds	Parameters affecting critical heat flux of nanofluids: Heater size, pressure orientation and anti-freeze addition

Design and implementation of a feedback linearizing controller and Kalman filter for a magnetic levitation system	Analysis of tapered laminated composite tubes under tension and torsion

An evaluation of using component mode synthesis for structural models	Flexible microfluidic circuit with embedded in-plane valve

Design, analysis and development of a morphable wing structure for unmanned aerial vehicle performance augmentation	Stress analysis of an ellipsoidal inclusion

Complete stress analysis for two dimensional inclusion problem using complex variables	Thermal enhancement of stacked dice replacing wire bonds with through silicon vias at location of die pads

Thermal stresses of composite beams with rectangular and tubular cross-sections	Design and analysis of multi-functional laparoscopic tool

An experimental study on thermal bonding effects of PMMA based micro-devices using hot embossing	Thermo-mechanical solutions in electronic packaging: Component to system level

Flip chip back end design parameters to reduce bump electromigration	Comparison of cooling performance of overhead and underfloor supply with rear door heat exchanger in high density data center clusters

Analytical thermal model of a generic multi-layer spacerless 3D package	Structural optimization using MATLAB partial differential equation toolbox and radial basis function based response surface models

Effects of edge distance, hole size ratio and hole spacing on peak stresses of composite laminate with multiple holes	Development of optical fiber sensors for distance, refractive index and strain measurement

Characterization of thermal challenges in electronics: Leakage current, co-architectural design and rack level cooling	Finite element analysis of helicopter main rotor hub plates to evaluate the possibility of increasing the time to retirement

Thermal design optimization of multi-passage internally cooled turbine blades	Effect of pullout and torsional strength of composites with co-molded thread inserts

High temperature microporous coatings: The effects of wetting and wicking on nucleate boiling and CHF	Thermo-mechanical interaction within engineered tissue during freezing

CAE tools for modeling inertia and aerodynamic properties of an R/C airplane	Structural optimization using Ansys Classic and radial basis function based Response Surface models

On the design of a biodegradable POC-HA polymeric cardiovascular stent	Electrowetting on dielectric (EWOD) digital microfluidics for electronic hotspot cooling

Fabrication of PLGA nanocomposite using two photon polymerization	Modeling and simulation of the flight dynamics of morphing wing aircraft

A numerical study on the dynamics of bubble growth and detachment from an orifice	Thermal management of outside plant telecommunication cabinets: Design and CFD modeling methodology

Effects of freezing on the mechanical properties of engineered tissues	Multiscale modeling of targeted drug delivery and DIEP flap perfusion

Thermo-mechanical analysis of a 3D package in microelectronics and cooling technologies for an IGBT thermal tester in power electronics	Dynamic thermal management of multi core processors using core hopping

Development of an optical fiber-based corrosion detection sensor based on laser light reflection	Analysis and design of a two-wheeled robot with multiple user interface inputs and vision feedback control

Passive RF sensors and wireless sensor interrogation	Kinematic analysis of a quadruped robot capable of working as a machining tool

Experimental study of the effects of thermally conductive microporous coatings on low heat flux pool and flow boiling	Applications of sensitivity data to eigensolution reanalysis of modified structures

A low cost micro scale cyclone separator - design and computational fluid dynamics analysis	Buckling and post buckling of structural components

Axial wave propagation in truncated cones	Alternative cooling technologies for telecommunication data centers: Air cooling and rear door heat exchangers

Experimental investigation of thermal behaviour of air foil bearings	Capacitive strain sensors for measurement of large strain for structural health monitoring

Imbalance response of a four degree of freedom rigid rotor supported by hybrid three pad air foil bearing	Multi objective thermal and energy based design optimization of telecommunication cabinets/shelters

Reanalysis for static and steady state structure response	Consideration of compressibility effects for applied-back-pressure dynamic well control response to a gas kick in managed pressure drilling operations

Numerical analysis of the interaction between a detonation wave and compressible homogeneous isotropic turbulence	Algebraic solution to the planar rigid body impact problem

The analysis and testing of the Quaife torque-biasing differential	Optimization of the tool path in a robotic environment

Analysis and optimal design of beams using radial basis function	Enhancement of pool boiling heat transfer using thermally-conductive microporous coating techniques

Analysis of hat-sectioned reinforced composite beams including thermal effects	System and method for the pooling of sterile product

Context-aware inference system, to capture design rationale from legacy MCAD	An analytical and numerical model for design of non-uniformly powered silicon chips based on both thermal and device clock performance

Stress distribution and strength prediction of composite laminates with multiple holes	A robust cooperative localization system for a heterogeneous team of small unmanned ground vehicles

Design for reliability in microoptoelectromechanical systems (MOEMS)	Closed-form development of a family of higher order tetrahedral elements through the fourth order

Methodologies for automated microassembly	A mathematical model development and sensitivity analysis of two photon polymerization for 3D micro/nano fabrication

The development and testing of pulsed detonation engine ground demonstrators	Semi-analytical complex variable based stochastic finite element method

Characterization and cooling capacity enhancement of a porous ceramic wick based coldplate	Development of a quantum dot mediated thermometry for minimally invasive thermal therapy

Experimental investigation of flow boiling and spray cooling on enhanced surfaces in FC-72	Topology optimization using hyper radial basis function network

Pool boiling heat transfer characteristics of nanofluids and nanocoatings	A unified analysis of stiffener reinforced composite beams with arbitrary cross-section

Effective thermal management of electronic devices from system to die level	Effect of structural design parameters on wafer level CSP ball shear strength and their influence on accelerated thermal cycling reliability

Ideal cycle analysis of a regenerative pulse detonation engine for power production	Development of an experimental and analytical model of an active cooling method for high-power three-dimensional integrated circuit (3D-IC) utilizing multidimensional configured thermoelectric modules

A one dimensional dry friction microconveyor platform: Modelling and analysis of micropart motion due to surface excitation	Lumped parameter modeling of fluid line dynamics with turbulent flow conditions