TOP >> ROCHESTER INSTITUTE OF TECHNOLOGY >> Mechanical engineering
 
Browse Institutions
You are viewing titles for ROCHESTER INSTITUTE OF TECHNOLOGY in the Mechanical engineering available through the UMI Dissertations & Thesis Gradwoorks site
 
Design and analysis of rocket nozzle contours for launching pico-satellites
 Experimental investigation on the effects of surface roughness on microscale liquid flow
 
Evaluation of a numerical thrombosis model for a high shear rotating flow
 On the determination of the elastic properties of geopolymeric materials using non-destructive ultrasonic techniques
 
Imaging the airways: 3D modeling of a complete respiratory airway for use in computational flow dynamics studies of particle deposition in the lungs. Creation of an educational animation about the respiratory system for use in the Human Visualization Project and CollaboRITorium
 The viability of a thermoelectric fuel conditioning system for a diesel engine utilizing biodiesel
 
Flow field analysis in an expanding healthy and emphysematous alveolar model using Particle Image Velocimetry
 Statistical model prediction of fatigue life for diffusion bonded Inconel 600
 
Robust longitudinal rate gyro bias estimation for reliable pitch attitude observation through utilization of a displaced accelerometer array
 An investigation into the viability of heat sources for thermoelectric power generation systems
 
Sliding mode control applied to an underactuated fuel cell system
 Feasibility assessment of a Kalman filter approach to fault detection and fault-tolerance in a highly unstable system: The RIT heart pump
 
Propellant tank pressurization modeling for a hybrid rocket
Determination of 3-dimensional deformations of the alveolar sac during simulated breathing
 
Control of a magnetically levitated ventricular assist device
Development of a novel method for autonomous navigation and landing of unmanned aerial vehicles
 
An optimization approach to plant-controller co-design
 Material selection for the actuator design for a biomimetic rolling robot conducive to miniaturization
 
Characterization of mass transport processes to enable PEM fuel cell start-up from low temperatures
 Investigation and development of advanced models of thermoelectric generators for power generation applications
 
Aortic valve performance with transaortic ventricular cannula
 Computational analysis of ultraviolet reactors
 
Locomotion of circular robots with diametrically translating legs: Design, analysis, and fabrication
 Scalability study for robotic hand platform
 
Stereoscopic particle image velocimetry analysis of healthy and emphysemic acinus models
 Determination of effective water vapor diffusion coefficient in PEMFC gas diffusion layers
 
Improved approximations for flows of thin films
 Scanning acoustic microscopy for GDL water distribution characterization
 
Dynamic modeling and characterization of a wind turbine system leading to controls development
 Estimates for the pressure and thermal distortions of coating dies for use in design and simulation
 
Development of a three-axis MEMS accelerometer
 Development of a Platform for Simulating and Optimizing Thermoelectric Energy Systems
 
Characterization of Two-Phase Flow in a Transparent PEM Fuel Cell using Simultaneous Anode and Cathode Visualization and Digital Image Processing
 Characterization and sensitivity analysis of hyperelastic materials in biaxial tension
 
Two dimensional rate gyro bias estimation for precise pitch and roll attitude determination utilizing a dual arc accelerometer array
 Application of non-invasive flow measurement techniques for quantitative analysis of a biomedical device
 
Design of a Test Loop for Performance Testing of Steam Turbines Under a Variety of Operating Conditions
 Experimental Study of Pool Boiling Heat Transfer Enhancement over Microchanneled Surfaces
 
Numerical Investigation of Fluid Flow and Heat Transfer Effects in Minichannels and Microchannels under H2 Boundary Condition
 Minimizing Temperature Droop and Power Line Flicker in a Lamp Heated Xerographic Fusing System
 
Robust adaptive control for a hybrid solid oxide fuel cell system
 Investigating controller performance in hybrid SOFC systems with unknown nonlinearities
 
State Estimation Filtering Algorithms for Vehicle Attitude Determination using a Dual-Arc Accelerometer Array and 3-Axis Rate Gyroscopes
 Effect of temperature on the in-plane permeability of the gas diffusion layer of a PEMFC
 
A Thermoelectric Generation Subsystem Model for Heat Recovery Simulations
 Evaluation of CFD based Hemolysis Prediction Methods
 
Flapping Wing Design for a Dragonfly-Like Micro Air Vehicle
 A Hemodynamic Investigation of a Complete Arteriovenous Model of the Arm, Arteriovenous Fistula, and Distal Revascularization and Interval Ligation
 
Scale-up of Algae Growth System to Cleanse Wastewater and Produce Oils for Biodiesel Production
 Design of passive suspension system with non-linear springs using B-spline collocation method
 
Feasibility of Integrating Multiple Types of Electroactive Polymers To Develop a Biomimetic Inspired Muscle Actuator
 Water Breakthrough Behavior and GDL Degradation Mechanisms in a PEM Fuel Cell
 
Verification and Validation of a Theoretical Model of a Direct Drive Valve-Controlled Electrohydrostatic Actuator for Primary Flight Control
 Center-of-Gravity Estimation of an Aircraft Solely Using Traditional Aircraft Measurement Sensors
 
Analysis of Translating Hydrofoil Power Generation Systems (Hydrokites)
 Analysis of the Environmental Impact on Remanufacturing Wind Turbines
 
A computational study of the effects of adherent leukocytes on secondary recruitment
 Electromechanical Actuator Bearing Fault Detection using Empirically Extracted Features
 
Characterization of Color, Gloss and Mechanical Performance of 3D Printed Structures
 Bruce, The Multi-Function Robot
 
Enhanced Pool Boiling of Water with Open Microchannels over Cylindrical Tubes
 Condition Monitoring of Reciprocating Compressor Valves Using Analytical and Data-Driven Methodologies
 
Feasibility of Capturing Circulating Tumor Cells With a Magnetized Device
 Geometric effects on the wear of microfabricated silicon journal bearings
 
A thermally actuated microelectromechanical (MEMS) device for measuring viscosity